Service Bulletins and Equipment Manuals
Service Bulletins and Equipment Manuals
As technology evolves, we strive to help you keep your equipment up-to-date. Below, you will find a list of service bulletins relating to Besser equipment. You will also find generic equipment manuals for standard Besser equipment.
Contact us for additional information: +1.989.354.1000 or 1.800.530.9991
Service Bulletins
- AFC Smartpac® Operating Instructions (SB2004‐1)
- Addition of 1/2″ Wedge Lock Washer to ASV Vibrator Drive Shaft Coupling (SB2015-6)
- Adjusting Second Stop on Besser Cam Operated Machines (SB1992‐2)
- Adjustments and Operation of Automatic Feed Control – Dynapac (SB2004‐4)
- Adjustments for 5‐5/8” High Units on a V‐4 or V‐4 (26” Deep) Machine (SB1997‐4)
- Agitator Encoder Set‐Points (SB1993‐5)
- Bescodyne Drive Service Tip (SB1993‐4)
- Bescodyne Solenoid Valves (SB2002-3)
- Bull Gear and Pinion Indexing and Replacement Recommendations (SB2001‐2)
- Bull and Pinion Gear Clearance and Alignment Procedure for MK3 Style Pinion Shafts (SB2000‐2)
- Gemco Cam Limit Switch Boxes (SB1995-2)
- How the Trabon Air Operated Grease Pump Works (SB1991‐2)
- How to Assemble a Besser Posapac Vibrator Shaft Assembly – Video
- How to Check the Bescodyne Clutch/Brake Stacks for Wear (SB1995‐1)
- How to Modify Air Compaction Device Air Cylinders to Reduce Rod Wear (SB1995‐3)
- How to Update Bescodyne Clutch/Brake Units from Single to Double Air Flow Valve (SB1994‐3)
- Improved Pneumatic Control System for Bescodyne Vibrators (SB1991‐1)
- Installation of KAMCO BOX to replace GEMCO BOX (SB2000‐1)
- Instructions to Move Electrical Box to Left Hand Side of Vibration Motor 312388 (SB1995‐4)
- New Style Crossport and Singling Plate (SB1995‐7)
- Pallet Lug Link Pins (SB2002‐1)
- Solutions to Correct Deformed and Cracked Blocks
- Tips to Extend Service Life of Bescodyne Units (SB1994‐2)
- Torque Specification for Tie Rods in Servopac Vibrator Module (SB2015-2)
- Troubleshooting the Digisolver for Allen Bradley SLC‐500 Programmable Logic Controllers (SB2004‐2)
- Ultrapac Anvil Configuration (SB2004‐5)
- Using the Encoder for Allen Bradley PLC‐2 Programmable Logic Controllers (SB1995‐5)
- Using the Encoder for Allen Bradley SLC‐500 Programmable Logic Controllers (SB1997‐1) – Updated 15 March 2011
- V3-12 Pallet Feeder Spring Adjustment (SB2024-1)
- V3‐12 Pinion Shaft Assembly Installation with Locking Assembly (SB1996‐5)
- Vibrator Motor Sheaves for Block Machines (SB1989‐3)AC
- Allen‐Bradley Panelview Self‐Test Numbers (SB2004-3)
- Besser NEMA and Current Transformer Type (SB1993‐2)
- Installing Screen Program in PanelView 900/1000 with a Flash Card (SB1999-2)
- Load Existing PanelView Plus 6 Graphic Terminal with New Application (SB2014-1)
- New PanelView Plus 6 Graphic Terminal Out of Box Setup (SB2014-2)
- New VersaView® Out of Box (SB2006-4)
- Open Rotor Test (SB2000-5)
- Procedure for Programming Allen Bradley 1336 Impact Frequency Drives When Used With AFC Smartpac Vibration (SB2004-7)
- Putting Allen Bradley SLC‐150 Controllers Back in the Run Mode (SB1992-1)
- SLC-500 Error Codes (SB2002-4)
- SLC‐500 Programmable Controller (SB1997-3)
- Troubleshooting the Digisolver for Allen Bradley SLC‐500 Programmable Logic Controllers (SB2006-15)
- T‐30 Plant Floor Terminal Set‐Up Information (SB1990-4)
- VersaView® Set IP Address (SB2006-2)
- VersaView® Start‐Up (SB2004-6)
- VersaView® Start‐Up Pt. 2 (SB2006-1)
- XYCOM 2050 Graphics Display Unit Set‐Up Information For Use with a PLC‐2 (SB1998-1)
- Besser Mold Assembly and Torque Requirements (SB1996‐4)
- Examples of How to Order Mold Parts (SB1996‐3)
- High Strength Vibrator Bolts (SB2001-1)
- Low Height Liners with 1” Keys (SB2004‐8)
- Mold Adjustments (SB2014-5)
- Mold Compartment Clearance Dimensions (SB1996‐2)
- Portable Mold Jig (SB1997‐6)
- Quick Order Reference Guide for Mold Pallet Guides (SB1993‐1)
- Quick Reference Guide for Ordering Agitator Grids (SB1990‐3)
- Recommendations for Use of Vibrator Weights (SB1997‐5)
You can now view your Mold Drawings or E-Books from this site. For more information contact Dave Miller, dmiller@besser.com or +1.989.354.1031.
Equipment Manuals
- Dynapac Operation & Maintenance
- Dynapac® Installation
- Superpac Operating & Maintenance
- Superpac Installation
- Ultrapac II 18.5″ Deep (4AAT) Operating & Maintenance
- Ultrapac II 18.5″ Deep (4AAT) Installation
- Ultrapac II 26″ Deep (4AAT) Operating & Maintenance
- Ultrapac II 26″ Deep (4AAT) Installation
- Vibrapac® Operation & Maintenance
- Vibrapac® Installation